QMY12-15 Mobile Hollow Block Making Machine – Full Range

Matched System Sourcing — the QMY12-15 mobile hollow block making machine is specified alongside its mixer, pallet handling and moulds as one coordinated line, not a standalone press assembled from separate vendors.

Technical Specifications

Application Suitability

What "13,000 Pieces per Day" Actually Means for a Mobile Block Making Machine Manufacturer

Capacity figures only hold weight when the block format, mix design, and curing conditions behind them are named.

Buyers often receive a daily output number without knowing whether it assumes a standard 400×200×200mm hollow block or a thinner paver that cycles faster. A mobile block making machine manufacturer quoting a single headline figure leaves the buyer guessing about real-world performance on their specific product. When the machine arrives and the actual format runs slower, the shortfall is blamed on the operator rather than the specification gap. [NEED_CITE: concrete block format dimensions and typical cycle time variation]

Placing the QMY12-15 Within the Full Mobile Range

This model sits at the higher output tier among egg-laying machines, producing 12 blocks per mold cycle. For buyers comparing options across the mobile block making machine manufacturer lineup, the QMY12-15 bridges the gap between small workshop units and stationary automatic lines. It suits sites where production must move with the building footprint rather than stay fixed in a plant.

Footprint and Site Logistics for Egg-Laying Production

Unlike a stationary press that needs a dedicated building, the QMY12-15 travels across a prepared ground slab and lays blocks directly on the floor. The electric motor handles forward and backward travel while hydraulic controls manage turning, letting one operator reposition the machine as the curing area fills. This mobility matters when the project site is large and blocks must be produced close to where they are laid. [NEED_CITE: site preparation requirements for mobile egg-laying block machines]

Reading the Specs That Drive Real Output

The dual vibration motor system compacts the concrete mix from two points, which improves density uniformity across the 12-block mold and reduces weak spots in the finished product. Hydraulic control of the upper press and demoulding shortens each molding cycle by applying consistent force rather than relying on mechanical springs. The 16 kW total power draw covers both vibration and hydraulic functions, so buyers must confirm their site generator or grid connection can sustain that load continuously. The heat dissipator on the hydraulic oil circuit prevents overheating during long shifts in hot climates, protecting seals and hoses from premature wear.

The Cost of Skipping the Format Conversation

When a buyer orders without confirming which block format the output figure assumes, the machine may arrive configured for a mold size that does not match local market demand. Mould swaps on a mobile unit take longer than on a stationary press with a quick-change system, cutting into the flexibility the buyer expected. Voltage and frequency mismatches discovered after arrival delay commissioning by weeks while transformers or replacement motors are sourced locally. [NEED_CITE: electrical standards and frequency variation across export markets]

Why Source This Mobile Range From a Single-Focus Supplier

Block machinery is the sole product line here, so the QMY12-15 host machine, JS7500 mixer, and optional batching equipment are specified as one matched system rather than assembled from unrelated vendors. Configuration is set against the buyer’s local aggregate and target block format, not a catalogue default. Mould design covers the formats the buyer’s market actually sells, including custom drawings when standard options do not fit. The automation level remains selectable, allowing a buyer to start with basic mobile operation and add batching or silo equipment later. Factory test records and packing photographs are provided before dispatch so the buyer can verify the machine matches the agreed specification.

Documentation & Verification

• Line layout showing ground slab dimensions and curing area required for QMY12-12 output
• Machine specification sheet covering vibration force, hydraulic pressure, and 16 kW power draw
• Mould drawing and format list confirming which block sizes the 12-cavity mold produces
• Voltage and frequency confirmation document signed before production begins
• Factory test record on the buyer’s target block format before dispatch
• Packing photographs showing dismantling and container loading arrangement

Installation, Commissioning & Support

• Ground slab must be level and cured to support QMY12-15 weight plus loaded dump truck traffic
• 16 kW power supply with dedicated circuit breaker and voltage matching confirmed on-site
• Machine arrives partially assembled; hydraulic turning system and vibration motors require field connection
• First production run supervised to set molding cycle against buyer’s local mix design
• Operator training covers electric travel controls, hydraulic demoulding, and heat dissipator maintenance
• Wear parts list for vibration motor bearings and hydraulic seals included with shipment

Preparing Your Inquiry

To receive a configuration that matches your site, share the block formats your market demands, the local aggregate and cement types available, and the daily volume you need to sustain. Confirm your site voltage, frequency, and whether a generator or grid connection will power the 16 kW load. Note the curing area dimensions you have available so pallet and handling recommendations align with your space.

Frequently Asked Questions

Q: How is the 13,000 pcs/day output figure calculated, and which block format does it assume?
A: That figure is based on an eight-hour shift, but the block format, mix design, and curing conditions behind it are not stated in the source data. Buyers should request a capacity calculation that names the specific block size and material assumed, so daily output expectations match their actual product.

Q: What voltage and frequency options are available for the target market?
A: Voltage and frequency are not listed in the standard specification and must be confirmed with the buyer before production. The supplier documents the agreed electrical configuration in writing to ensure the motor, control panel, and vibration system match the destination country’s grid or generator supply.

Q: How does a mobile egg-laying machine compare to a stationary line in terms of footprint and investment?
A: A mobile unit like the QMY12-15 lays blocks directly on a ground slab without needing a fixed plant building, conveyor system, or automatic stacker. This reduces initial site investment and suits projects where production must follow the construction area, though daily output and automation remain lower than a full stationary line.

Q: What optional support equipment is needed to run a complete mobile operation?
A: The basic configuration includes the host machine, JS7500 concrete mixer, and dump truck. Buyers can add a PL1200 batching machine, cement silo, screw conveyor, and loader to improve material accuracy and reduce manual handling, depending on their target volume and site layout.

Q: What mould formats can the QMY12-15 produce, and how long does a mould change take?
A: The machine handles hollow blocks, multi-hole blocks, solid blocks, curbstones, pavers, and interlocking blocks through mold swaps. Specific mold change time is not stated in the source data, so buyers should request this figure during configuration to understand how format flexibility affects daily scheduling.